*
Can be cut up and
used as single or double
(C) Stewart Dunn 2010 onwards
Blue clip connector
(strip of 4)
Can be cut up and
used as single, double
or triple as well
Green multiblock connector
(strip of 3)
‘Cap ends’
(insert in the
slit and snap rods)
Blue Collars
for use with
5mm tubes and rods
Only two unique patented Kre8 universal connectors,shown below, are needed to make all the models using rods
The connectors have a unique ‘built in hinge’ so joints can be ‘hinged’ and ‘animated’.as well as normal fixed static use.
Blue slit rods
5mm dia.
Blue slit rods
5mm dia.
Blue slit
rods 5mm dia
Light Blue tubes
5mm dia (4mm ID)
Blue snap Rod
5mm dia
Yellow Flexible snap
Rod 5mm dia
Spacer straw
6mm inside dia.
Orange bendy
tube 5mm dia.
Orange bendy
tube 5mm dia.
2mm hole is tight fit on motor spindle
Blue slit rods
5mm dia.
Blue slit rods
5mm dia.
Long lasting
pulley rubber
band
45mm
60mm
20T gear or
pulley
Long lasting
pulley rubber
band
wheel, pulley
or offset cam
wheel, pulley
or 40T gear
wheel, pulley
or 70T gear
Grey rubber collars
‘push fit’ on grey tube
3.9mm dia tube’
Wheels turn freely
on this tube
4mm dia ‘SNAP rod’
‘’push fit’ in wheels
A5 pattern holographic card
115x 210mmK064
Blue PP plastic
0.5mm x 70 x 180
nets printouts
FREE from website
Kre8 pipe and
tube cutter
Instructions on the web
www.kre8.com
Rule (metric)
Snips
(recommended)
or good
scissors
Side cutters
(to cut connectors up)
To use
rotate as
shown to
score rod
then
snap off
Single or
double
paper punch
FREE
FREE
Only needed if wanting
to laminate some of the
website drawings
Laminator
Plastic angle
multiblocks can be
clipped to the edges
Kre8 baseboard
210mm x 105 x 2.5mm
Dual purpose safety
propeller 75mm dia
Pushes onto motor spindle
.
Use as a
(1) normal or (2) as s flying propeller
Kre8 baseboard
1/2 size
5mm diameter rods and tubes of different lengths. Some can be snapped or cut to length as required.
The most useful slit rods push fit into 5mm diameter holes and the Kre8 connectors above
Rods and Tubes
A versatile range of mechanical parts compatable with other popular contruction kits.
They are all grey so they are easily identified and based on the wheels having a 4mm hole
A range of sheet materials that can be used with Kre8 parts and other specialist parts
Just a few basic tools are required. They can be obtained from stationary stores or
educational suppliers. For simple work just the tools marked ** are needed.
Basic Tools you may need
Other Useful Parts
Mechanical Parts
Blue slit rods
5mm dia.
K011N
K005N
K007N
KO53
KO33N
K011NB
K013N
K015N
K017
K055
K71
S009
K047A
K047B
X
X
K064A
K025N
K027N
K029N
K057N
K009
K056
K031N
K024
K019
K101
K100
K043N
K086
K110
Wire cutters
and stripper
K021
**
**
**
13-1324 Rapid
13-1332 Rapid
These connectors can be used
as supplied or cut up into
seperate units.
Red plastic strip polyproplene
400 x 35 x 0.5mm
1.5V Manual Motor controller for steering robots
via long wires. It uses one AA battery (1.5volts).
To connect link the 1metre wires provided
to the motors using the screw connectors.
For more information see a kre8 robot.
.
Connectors
3V Manual Motor controller for steering robots
via long wires. It uses two AA batteries.
To connect link the 1metre wires provided
to the motors using the screw connectors.
For more information see a kre8 robot.
.
To use accurately
remove the cover so
you can where the
cutting pin hole is when
cutting
